46
Technical / Re: Some help on leaning out my YZ250 please?
« on: August 16, 2010, 07:02:31 PM »Some would disagree with one aspect of that write up-but it's close enough
Everyone seems to have their own twist on this matter...
News:
Be sure to find us on fb,Twitter and YouTube!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Everyone seems to have their own twist on this matter...
48
Non-Moto / Re: yz250 trail riding
« on: August 16, 2010, 07:00:14 PM »
George! Watch out for that tree!! 
49
Non-Moto / Re: stupid craigslist prices.
« on: August 16, 2010, 06:58:22 PM »
They are wanting waayyy too much. I mean seriously, i just got my 2004 YZ250 for $1500....
$1900 for 1998's?
someone is in LaLa Land lol. 
$1900 for 1998's?
someone is in LaLa Land lol.
50
Technical / Some help on leaning out my YZ250 please?
« on: August 16, 2010, 09:10:36 AM »
Okay. So I know my bike is running too rich. And I Know it may need to be jetted. But I don't really know where to start? How do I go about leaning the carby out???
51
General Two Stroke Talk / Re: Motor to Pipe Gap??
« on: August 16, 2010, 08:49:35 AM »Braap,
If the "O" rings are fresh, you shouldn't need and RTV sealant. The o ring won't melt, but they tend to go hard after a while and lose their sealing quality.
The goop that's leaking out of your header pipe isn't caused by poor sealing at the cylinder, it's caused by overly rich jetting.
Put on fresh springs and "o" rings, get your jetting right and your problems will be cured for good.
Well, When i pulled the pipe off i don't believe any O-rings in were in there. But they will be in there soon enough. And i wasn't gunna use RTV on the around where the pipe connects to the motor. I was gunna use some for where the pipe connects to the silencer. As for the jetting, Yes i know its too rich. But I don't have the time to jet it myself right now. And being as I have never done it before it would probably take forever. I wonder if there was someone in my area who could do it for me?
52
Technical / Re: How to make front brake on my YZ feel firm???
« on: August 15, 2010, 08:31:11 PM »
I got them! They feel perfect. No sponginess whatsoever!!! I just bled and bled and bled and finally the lever smoothly goes back and is nice and responsive. 
53
General Two Stroke Talk / Re: Motor to Pipe Gap??
« on: August 15, 2010, 07:34:58 PM »Mkay thanks, Heres a pic of the springs. Is this why my pipes leaking?
Can I have the one on the left? I think it will fit my old stapler.
haha too funny
54
General Two Stroke Talk / Re: Anybody got some tips for riding in sand for me???
« on: August 15, 2010, 07:33:46 PM »Careful with the brakes especially front.Sand is great fun and you can ride super fast in it once the techniques is learned.Remember when in doubt throttle it out!
I will remember that.
55
General Two Stroke Talk / Re: Motor to Pipe Gap??
« on: August 15, 2010, 06:16:19 PM »
Mkay thanks, Heres a pic of the springs. Is this why my pipes leaking?
56
General Two Stroke Talk / Re: Motor to Pipe Gap??
« on: August 15, 2010, 05:56:13 PM »
This week is looking to be a good one! On wed my fmf pipe spring and o ring kit will be in along with the spring puller
And on thurs my new Jersey, Pants, Renthal Bar pads "For the Renthal Handle bars of course
" My oil plug and some stickers i bought
Now for the questions. I figure RTV stuff shouldn't go where the pipe connects to the motor as it may be too hot and with new springs and an o ring is shouldn't need it right? And i plan on using the RTV to get a solid seal where the pipe connects to to the silencer.
And on thurs my new Jersey, Pants, Renthal Bar pads "For the Renthal Handle bars of course
" My oil plug and some stickers i bought Now for the questions. I figure RTV stuff shouldn't go where the pipe connects to the motor as it may be too hot and with new springs and an o ring is shouldn't need it right? And i plan on using the RTV to get a solid seal where the pipe connects to to the silencer.
57
General Two Stroke Talk / Re: Motor to Pipe Gap??
« on: August 15, 2010, 03:13:17 PM »
guys, guys, guys. There is room for everyone's opinion lol.
Anyways, Pulled the pipe and silencer today and got them both completely oiless. gunna get the FMF pipe and o-ring kit as i heard its the best. About to go to walmart to get some clamps for the exhaust hose "as obviously i had to cut the old ones off" And as somebody mentioned before to get some RTV and I did. Picked some up at the AutoZone a few days ago. So everything is nice and clean and will be sealed perfect
Anyways, Pulled the pipe and silencer today and got them both completely oiless. gunna get the FMF pipe and o-ring kit as i heard its the best. About to go to walmart to get some clamps for the exhaust hose "as obviously i had to cut the old ones off
" And as somebody mentioned before to get some RTV and I did. Picked some up at the AutoZone a few days ago. So everything is nice and clean and will be sealed perfect
58
Technical / Re: How to make front brake on my YZ feel firm???
« on: August 15, 2010, 07:08:41 AM »
Okay thanks Ford I will try that.
59
General Two Stroke Talk / Re: Anybody got some tips for riding in sand for me???
« on: August 15, 2010, 07:04:50 AM »
So basically don't be afraid to use the throttle? Okay.
60
General Two Stroke Talk / Re: Anybody got some tips for riding in sand for me???
« on: August 14, 2010, 03:43:18 PM »Which track are you going to? And have you gone ridding at Croom yet? It would be best to start riding at a place like Croom or go on school day at your track and go with the beginers to start with. Most of the guys at local track are very fast hard to learn with.
Bartow Motocross is my local track. And no haven't gone to croom. Haven't gone anywhere yet. Some buds of mine who ride quads invited me to go out to Suburban Estates in Holopaw Florida, since they own land out there. there is mud, sand, clay, and everything in between.