Coming Soon
Home > Forum


Author Topic: '81 yz250 build  (Read 6764 times)

0 Members and 1 Guest are viewing this topic.

Offline riffraff

  • Professional
  • *****
  • Posts: 487
  • Still smokin' after all these years
    • View Profile
« Last Edit: December 31, 1969, 04:00:00 PM by ' »
aaahhhhh yes, I remember the good old days

Offline xs850triple

  • Posts: 0
    • View Profile
'81 yz250 build
« Reply #16 on: June 19, 2013, 05:11:18 AM »
How can I measure that?
« Last Edit: December 31, 1969, 04:00:00 PM by ' »

Offline xs850triple

  • Posts: 0
    • View Profile
''81 yz250 build
« Reply #17 on: June 19, 2013, 09:32:34 AM »
Also is there anywhere where I can find I guess a parts explosion or something to see how all my fancy new bearings go back together.. they came out destroyed, and there's still some old junk in there I'm not sure what to do with, ill get pics in the morning
And thanks for all the help so far guys, yall have been great
« Last Edit: December 31, 1969, 04:00:00 PM by ' »

Offline TMKIWI

  • Professional
  • *****
  • Posts: 1634
    • View Profile
« Last Edit: December 31, 1969, 04:00:00 PM by ' »
If you don't fall off you are not going hard enough

Offline xs850triple

  • Posts: 0
    • View Profile
''''''''81 yz250 build
« Reply #19 on: June 19, 2013, 08:15:35 PM »
Ooh perfect! That'll help a ton! So here's some of the new parts from all balls bearingngs :)
« Last Edit: December 31, 1969, 04:00:00 PM by ' »

Offline xs850triple

  • Posts: 0
    • View Profile
''''''''''''''''81 yz250 build
« Reply #20 on: June 19, 2013, 08:36:47 PM »
So I'm havin trouble matchin some stuff up, one is the sleeves that mount the rear of the engine, I still have one in good shape, but I cut through the other one, I can't find these for sale, do I just reuse the one I cut and I can throw some washers on there to bring it up to the right size? You can see the one I removed above the old bolt, the other one is still seized to the bolt where I cut it off
« Last Edit: December 31, 1969, 04:00:00 PM by ' »

Offline xs850triple

  • Posts: 0
    • View Profile
''''''''''''''''''''''''''''''''81 yz250 build
« Reply #21 on: June 19, 2013, 08:43:16 PM »
The other big thing I can't figure out to do with is the the ends of the swingarm are all mutilated, and I just don't know what to do with them, the little ring you can see looks about the same on both sides, like it got ripped out and its missing a piece, do I try and get the rest of that out? Or is it not suppose to come out
« Last Edit: December 31, 1969, 04:00:00 PM by ' »

Offline evo550

  • Expert
  • ****
  • Posts: 240
    • View Profile
Looks like there are some parts missing from the all balls kit.
There should be two flat bearings that sit between the copper washer and the dust cover, the bits are No 2 in the parts fiche.
« Last Edit: December 31, 1969, 04:00:00 PM by ' »

Offline xs850triple

  • Posts: 0
    • View Profile
These 4? The yellow washers are the copper washers on the back, the old stuff is there to, so I'm guessing those yellow/copper washers go in place of the needle bearings with a silver washer on each side right, also inside the swing arm I pulled out two plastic sleeves that size whise matched up with silver bearings in the kit, so I guess those swap.. now the two little plastic pieces in the top of the pic, I can't find anything on the old stuff that resembles them, where do those go?
« Last Edit: December 31, 1969, 04:00:00 PM by ' »