Author Topic: anyone come up with a better mousetrap? (Read 7902 times)

coblefutch · « **on:** July 01, 2012, 02:13:41 PM »

I just rounded the head on my 2nd oil drain plug this year on my 05 YZ. I even went out an bought a new socket (6 sided) just for this after ruining the first one. I took the new plug to sears and picked the socket that fit the plug the best. Still rounded it off.
They don't give you much to bite on and the metal on this thing is like butter. I like to change my oil every two races and now I the only way I will get the rounded plug out is to drill a hole in the center of it and use an easy out.
What am I doing wrong? and or does someone make an aftermarket plug the is better, larger head or better materials..

nom de guerre · « **Reply #1 on:** July 01, 2012, 02:31:04 PM »

Too much torque.. Just snug it. I have never stripped or rounded a drain bolt.

rookie · « **Reply #2 on:** July 01, 2012, 02:59:39 PM »

yes, just snug it will do.

ya might need new crush washer to help you with it.

Charles Owens · « **Reply #3 on:** July 01, 2012, 03:19:24 PM »

I always use magnetic aftermarket plugs. They usually have a larger head and better material

metal_miracle · « **Reply #4 on:** July 01, 2012, 05:24:02 PM »

i have rounded some too.

what i did was grind down to next smaller size socket, just a Thad bigger so you knock it on..

Another way i did was much more simple, I took of clutch cover and drained that way.

It may work if you don`t get a replacement

streaks383 · « **Reply #5 on:** July 01, 2012, 05:29:43 PM »

Like the guys said just snug it, but I got mine stuck in there, came that way when I bought, and had to have it machined out. I replaced it with a moose magnetic one, the bottom had a much larger hex head on it.

HCE · « **Reply #6 on:** July 02, 2012, 03:00:37 AM »

Buy an inch pound torque wrench and use it every where on the bike. You will be surprised at how little the bolts are tightened. Drain plug is only 17 ft lbs. After a while of using the torque wrench you will get a better feel for how tight bolts are supposed to be. I will bet anyone not using a torque wrench including myself is over tightening bolts. Also if you do not have a torque wrench please do not touch your triple clamps.

fabbo · « **Reply #7 on:** July 02, 2012, 06:31:17 AM »

I had the same problem on my YZ had to get the shop to remove it. I asked what could i do to stop it, he said buy a six sided socket to fit the plug not the twelve notched type sockets. So I bought a six sided socket just for the drain plug and have never had any problems since. He advised me six sided sockets are better tools than 12 notched type, they are definitely more expensive and they fit grip better.

coblefutch · « **Reply #8 on:** July 03, 2012, 05:33:29 PM »

Thanks all for the input, I plan on doing all of the above. I will replace it with a Moose plug and start using my inch lb wrench.
The sad thing is I am anal about torque on every other fastener but have never torqued these plugs.

rsmith · « **Reply #9 on:** July 04, 2012, 02:07:35 AM »

I have had a little better luck with the gytr bolt and it has a magnet also. When mine get rounded I use vise grips and put in another new bolt.

Jeram · « **Reply #10 on:** July 04, 2012, 02:10:22 AM »

Is it just me or am I the only one who has never rounded off a sump plug?

(and my 17mm spanner is chinese made haha)

TMKIWI · « **Reply #11 on:** July 04, 2012, 09:12:09 AM »

Quote from: Jeram on July 04, 2012, 09:10:22 AM

Is it just me or am I the only one who has never rounded off a sump plug?

(and my 17mm spanner is chinese made haha)

No its not just you.

beaner · « **Reply #12 on:** July 04, 2012, 10:31:14 AM »

I was wondering the same thing.

scotty dog · « **Reply #13 on:** July 04, 2012, 11:34:48 AM »

make that 4 of us

msmola2002 · « **Reply #14 on:** July 04, 2012, 01:57:20 PM »

Not stripped a sump but have stripped a carby bowl where the 17mm cover goes over the main jet

News:

Author Topic: anyone come up with a better mousetrap? (Read 7902 times)