Messages

1

Photos & Videos / 2005 CR 125 build

« on: June 05, 2012, 08:24:45 PM »

it deffinitly has a lot more hit down low but the mid is where i noticed the biggest difference. when all was stock it had a very short rpm range that you could ride it in, more so than any other 125 ive rode it was super peaky. the pipe, silencer and reeds gave me a lot more usable power range. i met a guy at the track who had a 06 or 05 cr 125 and he said he threw on a pc pipe and silencer then switched to fmf and said there was a huge difference between the two with the fmf giving more power through out. the other thing is that i havent had time to dial in the jetting but it was supppperrr rich stock and even though i put the pipe and reeds it still seems to run really rich.

2

Photos & Videos / 2005 CR 125 build

« on: June 04, 2012, 09:48:17 PM »

Hey whats going on guys, so i started with a bone stock 05 cr 125 they still had the orginal tires, chain ect. I havent done a whole lot to the engine im waiting tell things start to wear out before i really start tearing into it. but here is a list of the things i have done.
Renthal bars, pro taper grips, avs unbreakable levers, new tires, renthal chain and sprokets, warp 9 complete wheels, pc platium exhuast, vforce 3 reeds, twin air filter, graphics, i might be forgetting a few things but thats about it.

3

Photos & Videos / Re: Day at the track

« on: October 05, 2011, 11:24:53 AM »

I forgot to add that these are from my 21st bday...What better place to spend your bday then at the track?

4

Photos & Videos / Day at the track

« on: October 05, 2011, 11:03:22 AM »

First off i want to give a big shout out to TSM's own Andrew Cameron for taking me to the track (OPMC). Ive never really rode an actual track before and it was a blast. He gave me tips on cornering and pushed me to try bigger jumps. Here are a couple pics of us having some fun.
http://s91.photobucket.com/albums/k287/mxboy721/tyler%20and%20andrew/

5

Technical / Re: Jetting Question

« on: September 23, 2011, 09:18:59 PM »

just got home today opened my box and pulled out my pipe and it had a big dent in it..

6

Technical / Jetting Question

« on: September 19, 2011, 08:45:03 AM »

Hey guys, so fishing season is finally over (thank god) and now its time to spend a little hard earned money. i just ordered a pc exhaust with the shorty silencer and a vforce 3 reed cage. i was wondering if this is gonnna screw with my jetting? the bike is a bone stock 2005 cr 125. I will prolly order more goodies for it so i will post some pics once its all put back together.

7

Technical / Re: carb problems

« on: May 18, 2011, 05:34:59 PM »

Got the bike fixed yesterday with only a week to spare until i leave...thanks everyone

8

Technical / Re: carb problems

« on: May 12, 2011, 01:06:07 PM »

hey so i have the bike torn down again...the float chamber gasket got messed up (most likely during reinstall)..the bike seemed to run smoother but still wide open after i cleaned everything. do you think i fixed the original problem and now it is the gasket that is the problem?

9

Technical / Re: pw 80 oil injection or pre mix

« on: May 11, 2011, 12:19:58 PM »

on my first bike (ds 80) i had to do the same thing..keep it premix. i think i ran mine about 40:1 you really wont need to go lower than that

10

Technical / Re: carb problems

« on: May 10, 2011, 11:31:15 AM »

so i cleaned the carb...all the jets seemed to be fine. now it will start without blowing into the overflow tubes but it still is stuck wide open. my throttle cable seems to be work just fine. anybody have any ideas?

11

Technical / Re: carb problems

« on: May 08, 2011, 11:53:55 PM »

ok i have the bike torn down now..the carb looks fine but why would blowing in the over flow tubes make the bike start with a frayed throttle cable

12

Technical / carb problems

« on: May 08, 2011, 01:55:22 PM »

hey guys so i just got back from alaska and my bike has been sitting for a couple months (2005 cr 125). i had my cousin come a ride it around for a little bit while i was gone. i went to start it yesterday and it wouldnt fire..i changed the plug and it still wouldnt go. i think he might have ran some bad gas in it because i blew into the over flow tubes and it started but was stuck wide open. im thinking maybe the floats are stuck open but im not a very good mechanic. what are your thoughts

13

General Two Stroke Talk / Re: Show us your ride.

« on: March 14, 2011, 06:57:04 PM »

Im leaving friday for juneau. i might end up in sitka delivering fish though

14

General Two Stroke Talk / Re: Show us your ride.

« on: March 13, 2011, 09:33:43 PM »

ya that would be cool. im leaving at the end of the month it sucks

15

General Two Stroke Talk / Re: Show us your ride.

« on: March 13, 2011, 01:01:29 PM »

i know i really want to. the only problem is i fish in alaska all summer so i never get any decent weather to ride in.