Messages

1

Photos & Videos / 95 yz 125 progress

« on: May 10, 2013, 11:14:24 PM »

I'm about to start it. hopefully I'll be riding tomorrow

2

Photos & Videos / another project

« on: April 16, 2013, 11:41:29 PM »

89 KX500. Needs some TLC but its in pretty good condition

3

Photos & Videos / 95 yz 125 progress

« on: April 09, 2013, 07:06:51 PM »

i don't have much left to do just waiting on a clutch basket. the rear brake piston wont compress either so i may need to find a caliper.

4

Photos & Videos / 95 yz 125 progress

« on: April 09, 2013, 03:09:26 AM »

making progress but not finished yet. looks better than what i started with.

5

General Two Stroke Talk / Anybody use these graphics before?

« on: March 26, 2013, 12:27:35 AM »

im thinking of buying the chesterfield yamaha graphics off these guys and want to know if anybody out there has used them before. they are made in england.

http://www.evo-mx.com/mall/EvoMx/

6

Photos & Videos / $300 cr 250

« on: March 04, 2013, 01:27:30 AM »

no it doesn't run yet. the guy i bought it off of was changing the side cover gasket and cracked the side cover and the case. found the case on eBay already. has good compression but I'm probably gonna throw a new piston and rings in it

7

Photos & Videos / $300 cr 250

« on: March 04, 2013, 12:44:27 AM »

its a 95. i couldn't pass it up.

8

Photos & Videos / $300 cr 250

« on: March 03, 2013, 11:32:23 PM »

picked this up today for $300. Needs some tlc

9

Photos & Videos / KDX 220 before and after

« on: November 16, 2012, 11:35:04 PM »

yes carb is still stock. took it out today and it was running very rich. almost have it running right. the floats stick. i replaced the float valve and set the height. that may be why it seems to run rich.

10

Photos & Videos / KDX 220 before and after

« on: November 14, 2012, 01:26:46 PM »

took me a few months but i finally got it done. working on a 95 yz 125 which is the last pic. not gonna have it done until january.

BEFORE



AFTER


NEXT

11

Photos & Videos / first ride on the 02 yz 125

« on: May 01, 2012, 02:25:57 PM »

finally got a go pro. tested out the 02 yz 125 for the first time this weekend also. it was pretty slick in some spots but im going again this weekend and it should by dry. 


 

12

Photos & Videos / 1 down 2 to go

« on: April 20, 2012, 10:35:30 PM »

i got one of the yz's done today


what i started with





what it looks like now

13

Technical / yz 125 piston

« on: March 27, 2012, 02:46:05 PM »

also could not find the marking so the only way for me to know is to measure. i am just worried about putting the bigger piston in the smallest cylinder.

14

Technical / yz 125 piston

« on: March 27, 2012, 02:40:19 PM »

i did not know about the A,B,C,& D cylinders and the pistons that go with them when i got started. the bad thing about it is that i have the manual  and didn't bother checking. the cylinders are marked on the intake side. i am going to have to measure the cylinder when it comes in and see what they replated it to. The difference is .004mm between the cylinders and about .004 with the pistons. kinda sucks i jumped right into buying parts and not checking

Cylinder A 54.000-54.002      Piston A 53.957-53.960
Cylinder B 54.004-54.006      Piston B 53.961-53.964
Cylinder C 54.008-54.010      Piston C 53.965-53.968
Cylinder D 54.012-54.014      Piston D 53.969- 53.972

15

Technical / yz 125 piston

« on: March 26, 2012, 11:39:22 PM »

i started working on the 02 yz 125 project but i wasn't paying attention to the A,B,C,& D when i ordered the piston. I ordered the D and have a replated cylinder on the way. Will the D piston work with a new plated cylinder?