Messages

1

Technical / Base Gasket Sealant

« on: November 25, 2012, 03:17:37 AM »

Most kids my age want fancy clothes or money for Christmas.  I however have reason to believe santa is bringing me a top end rebuild kit from Weisco in the near future.  The bike is a 2005 yz250(as if my name didn?t give it away). I am getting a slight spooge escaping on the clutch side of the base gasket.  I was curious what type of sealant to use when I button everything back up to avoid future leaks.  Any help is greatly appreciated.  Keep on smokin' everyone. Braaaaaaap.

2

Open Forum / Freshman Tomorrow :/

« on: August 24, 2012, 04:32:04 AM »

Gonna be a college freshman myself come wednesday. Don't sweat it the transition between middle to high school is small. I'm a littel scared of engineering school though

3

For Sale / 2004 RM 250

« on: July 15, 2012, 10:17:23 PM »

Have you ridden at tomahawk in the past month? If so I can back you up that this is one amazing bike as I have seen it run and it is a truly amazing machine.

4

Technical / Detonation

« on: July 15, 2012, 04:15:19 PM »

Thank you all so much for the detailed info.  So there really are no signs of detonation at idle? (I'm assuming unless it is way too lean etc.)

5

Technical / Detonation

« on: July 14, 2012, 11:55:49 PM »

What is detonation and how do you identify it as compared to two stroke rattle?  I'm simply curious and have never been 100% sure about it.

6

Technical / My Bike is eating plugs

« on: May 31, 2012, 10:31:05 PM »

What heat range plug are you running? I used to run a br9eg and would foul at least one every time I rode.  After switching to an 8, i am still on the same plug after six months.  Look in your manual and see what heat range plug the factory calls for.  Hope this helps

7

Photos & Videos / Chris Blose YZ 250 Pics

« on: May 18, 2012, 12:21:32 AM »

 Found this on facebook!! sick bike

8

Non-Moto / How big have you gone?

« on: May 16, 2012, 03:06:31 AM »

110 foot table. 3rd gear pinned

9

Open Forum / how old are you?

« on: April 08, 2012, 04:18:06 PM »

17 Started riding quad at 12 and bought a 1994 kx250 for my first bike at 14.  Have since been through one thumper (wr400f which was a trail monster) and am now happily on a 05 yz250.

10

Technical / Is this too lean?

« on: April 03, 2012, 11:54:19 PM »

I find it to be just a little too sloppy from like 1/8 to 1/4 throttle.

11

Technical / Is this too lean?

« on: April 03, 2012, 01:02:31 AM »

Will do when I get the chance.

12

Technical / Is this too lean?

« on: April 02, 2012, 10:27:16 PM »

Hello once again I have to tune my bike to get better and better response ( go figure).  Right now i run a 178 main with a 50 pilot, air screw 1 turn out with a stock pipe and pro circuit long silencer.  My elevation is 550 ft and the average humidity is 80%.  My question is, would going to a 175 main and a 48 pilot be too lean?  I put them in and can definitely feel the difference in throttle response around the yard, but im afraid when I am out pinning it on the track the bike will be too lean? Is this true or am I just being too cautious? I just want some more response without burning up the bike.

13

Technical / 05 yz 250 silencer

« on: March 23, 2012, 07:25:02 PM »

I run the stock pipe with the pc 304 long silencer. Simply put, I love it.  It has a nice deep exhaust tone when you wind it out and is smaller and lighter than stock.  Also, you do not need to rejet for the new silencer.

14

For Sale / Procircuit works pipe

« on: March 12, 2012, 12:17:59 AM »

Wont freezing it put hairline cracks into it?

15

For Sale / Procircuit works pipe

« on: March 11, 2012, 09:12:22 PM »

I know it sucks! I could deal with all of the other ones but that one is just massive :/ I wish there was a way i could just pull it out instead of sending it to pipe repair.